Reduce Gas Price

3M 08963 Do-It Yourself Fuel System Tune Up Kit

• Helps to restore power and save on gas mileage
• As simple to perform as an oil change
• Requires a few unadorned hand-tools
• Detailed instructional DVD included with kit

A three part kit designed for the ‘medium’ to ‘heavy’ do-it-yourselfer to perform a qualified fuel system cleaning at home. Contains 3M DIY Intake System Cleaner (PN 08954), 3M Strangle Plate and Carb Cleaner (PN 08185) and 3M Complete Fuel System Cleaner (PN 08813).

The 3M Do-it-yourself Fuel System Tune-up Kit is a economical solution for achieving qualified mechanic grade fuel efficiency and performance out of fuel systems, at a do-it-yourselfer price. Made up of three quality 3M automotive products — 3M Do-it-yourself Intake System Cleaner, 3M Strangle Plate and Carb Cleaner and 3M Complete Fuel System Cleaner — together they work to remove carbon, varnishes at soot from all areas of your fuel system. This simple to use tuning system is useable by virtually any would-be mechanic and includes detailed instructions on DVD.

Qualified quality fuel system clean-up.
View larger.

Step 1: allow DIY Intake System Cleaner to be taken into the system.
View larger.

Step 2: apply Strangle Plate and Carb Cleaner frankly to strangle plate surfaces.
View larger.

Step 3: Add 3M Complete Fuel System Cleaner to a full tank of gas and drive.
View larger.

Increase Fuel Nation, Power and Hastening

Since no engine is 100% efficient, carbon, resins, and varnishes eventually erect up in critical engine components, causing a reduction in fuel nation, power and hastening. Until now car owners needed to pay for a qualified fuel system service to remedy this, which can be very costly. But now 3M has provided do-it-yourself consumers with a fantastic new way to get maximum performance from their vehicles from the convenience of their own home garage, for less than ½ the cost of what they would pay for the same consequences at a service center, with the 3M Do-it-yourself Fuel System Tune-up Kit.

DIY Solution in 3 Simple Steps

The 3M Do-it-yourself Fuel System Tune-up Kit combines the strengths of three quality 3M automotive maintenance products into a single fuel system tune-up program that when performed annually, or every 10,000 miles, will improve vehicle performance and gas mileage. These three products are: 3M Do-it-yourself Intake System Cleaner, 3M Strangle Plate and Carb Cleaner and 3M Complete Fuel System Cleaner. The steps involved in this administer are simple to perform and can feasibly be done by a single person, but are more easily achieved with the aid of an assistant behind the wheel at particular stages.

• Step 1 – 3M Do-it-yourself Intake System Cleaner: Follow the fresh intake hose to the outside of your engine’s strangle body. Remove the hose boot clamp everywhere it enters the strangle body with a screw driver to door the strangle plate. Insert the 3M Do-it-yourself Intake System Cleaner’s attached hose past the strangle plate and slip the intake hose boot back on. With the help of an assistant, initiation the car engine even as the work area is monitored. When the engine idle reaches 500-1,000 RPM, hold steady at this rate and spray the product’s contents into the running engine. This administer cleans intake manifolds, valves and combustion chambers. Use the entire can, which may take numerous minutes. Turn off the engine, remove the product hose and proceed to step 2.
• Step 2 – 3M Strangle Plate and Carb Cleaner: Again, with the help of an assistant, place the vehicle ignition in the “Run” spot, but with the engine NOT ongoing, and depress the accelerator to expose both sides of the strangle plate. Spray both sides of the plate, as well as the strangle body with 3M Strangle Plate and Carb Cleaner. Wipe excessive cleaner away and/or let wet areas dry for a few minutes with the strangle plate open before you replace the fresh air hose boot, tighten it up. This administer cleans your engine’s strangle plate and lubricates key pivot areas. Proceed to step 3.
• Step 3 – 3M Complete Fuel System Cleaner: This last step continues the behavior of all critical fuel system components. Add 3M Complete Fuel System Cleaner to a full tank, at a not compulsory delusion ratio of one ounce of additive to each gallon of fuel. Initiation the engine, allowing it to idle for a few minutes before driving it for 10-15 minutes. 3M Complete Fuel System Cleaner cleans injectors, intake valves and an combustion chambers even as your engine consumes this tank of gas.

Key Features

• Helps to restore power and save on gas mileage by cleaning air intake and fuel systems
• Simple, quick three-step procedure is even more unadorned to perform than an oil change
• Requires only a few common hand-tools and safety items
• Detailed instructional DVD included with kit

What’s in the Box

• 1 – 8.75 oz. canister of 3M Do-it-yourself Intake System Cleaner
• 1 – 4 oz. canister of 3M Strangle Plate and Carb Cleaner
• 1 – 16 fluid oz. bottle of 3M Complete Fuel System Cleaner
• 1 – DVD instructional video

Limitation of Liability

Except everywhere prohibited by law, 3M will not be liable for any loss or hurt arising from use of this 3M product, whether direct, indirect, special, incidental or consequential, in any case of the legal theory asserted, including warranty, contract, negligence or strict liability.

About 3M

A recognized leader in research and development, 3M produces thousands of innovative products for dozens of diverse markets. 3M’s core strength is applying its more than 40 distinct technology platforms – evenly in amalgamation – to a wide array of consumer needs. With billion in sales, 3M employs 75,000 people worldwide and has operations in more than 65 countries.

List Price: $ 51.99

Price: $ 36.00